Gaps between doors, doors and body, luggage compartment lid and body, mm | 4 ± 1 |
Maximum admissible gap unevenness, mm | 1 |
Displacement of the plane of the door / lid of the luggage compartment relative to the plane of the body, no more than, mm | 1 |
Clearances between the hood and headlights / front bumper, mm
a — 4 ± 1
b — 5 - 1
c — 2.5 ± 1
Protrusion of the front edge of the hood relative to the upper edge of the headlamp lens - 2 mm
Gaps on windows and doors, mm
A — A:
a — 5 ± 1
b — 21 ± 1
B — B:
a — 12 ± 1.5
b — 12 ± 2
C — C:
Preload
a — 2.5 ± 1
b — 12 ± 1.5
c — 12 ± 2
D — D:
Preload
a — 1.5 ± 1
b — 12 ± 1.5
c — 12 ± 2
E — E:
a — 12 ± 2
b — 37 ± 1.5
F — F:
a — 21 ± 1
b — 5 ± 1
H — H:
a — 5±1
b — 21 ± 1
I — I:
a — 21 ± 1
b — 7 ± 1
G — G:
a — 12 ± 2
b — 12 ± 2
c — 5.5 ± 1
L — L:
a — 2 ± 1
K — K:
a — 21 ± 1
b — 7 ± 1
Control body dimensions, mm
Dimensional tolerances up to / over 1000 mm are respectively±1 /±2 mm. In parentheses are the dimensions for the version with an extended base L; in double brackets - for the version with an extended base L7.
A - Front shock damper bracket
B - Front strut mount
C - Front top platform for jacking
D - Rear upper platform for the jack
G - Rear strut mount
P - Axis of the center of the front upper fixed hinges
Q - Axis of the center of the front lower fixed loops
R - Axis of the center of the rear upper fixed loops
S - Axis of the center of the rear lower fixed loops
P - Axis of the center of the front upper fixed hinges
Q - Axis of the center of the front lower fixed loops
R - Axis of the center of the rear upper fixed loops
S - Axis of the center of the rear lower fixed loops
A - Front shock damper bracket
B - Front strut mount
C - Front top platform for jacking
H - Front axle beam mounting
I - Rear mount of the front axle beam
D - Rear upper platform for the jack
E - Front mount rear axle beam
F - Rear axle beam mounting
G - Rear strut mount
M - Rear shock damper bracket
O - The middle of the floor of the trunk
B - Front strut mount
G - Rear strut mount
E - Front mount rear axle beam
F - Rear axle beam mounting
H - Front axle beam mounting
A - Front shock damper bracket
B - Front strut mount
H - Front axle beam mounting
I - Rear mount of the front axle beam
J - Fitting of the front axle beam
K - Front console of the transmission mounting beam
L - Middle console of the transmission mounting beam
E - Front mount rear axle beam
F - Rear axle beam mounting
G - Rear strut mount
M - Rear shock damper bracket
N - Trunk floor transverse beam, diameter 20 mm
Tightening force of threaded connections, Nm | |
Front bumper with shock absorber bracket | 41 |
Impact damper/front bumper bracket to body | 9 |
Rear bumper/support beam to impact damper | 45 |
Seat belt to body (except for the center pillar) | 48 |
Seat belt to B-pillar | 31 |
Seat belt height adjuster bolts to body | 24 |
C-pillar trim to body | 3 |
Front seat to underbody | 42 |
Trim to front seat rail | 4 |
Front seat frame to seat rail | 15 |
Rear seat back to body | 5 |
Sunroof cover drive cables to cassette | 1.3 |
Glass cover to yoke | 4.5 |
Sliding ceiling panel to stage | 1.5 |
Windshield support to cassette | 1.2 |
Stop to sliding ceiling panel (sunroof with glass cover) | 0.9 |