Suspension — equipment and tools
Drawing Name and code 312240 - 312247 Puller 334200 Tool kit/mandrel 312230 Socket head 313210 Key 313340 Spring compressor 313350 Spring compression horn...
Drawing Name and code 312240 - 312247 Puller 334200 Tool kit/mandrel 312230 Socket head 313210 Key 313340 Spring compressor 313350 Spring compression horn...
Stiffening plate
Removal and installation the stiffening plate Attention: Observe safety precautions when lifting a vehicle. Driving without a stiffening plate is prohibited....
Removal and installation the stiffening plate Attention: Observe safety precautions when lifting a vehicle. Driving without a stiffening plate is prohibited....
Front suspension cross member
Replacing the front suspension cross member Caution: Secure the engine in its mounting position to prevent it from falling. 1. Disconnect the negative cable...
Replacing the front suspension cross member Caution: Secure the engine in its mounting position to prevent it from falling. 1. Disconnect the negative cable...
Transverse suspension arm
Removal and installation the left or right wishbone Note: If the wishbone was disconnected from the front suspension crossmember, the wheel alignment must be...
Removal and installation the left or right wishbone Note: If the wishbone was disconnected from the front suspension crossmember, the wheel alignment must be...
Hinge in the pivot bearing
Removal and installation the hinge in the swivel support 1. Remove the front wheel. 2. Loosen the nut (1), holding the fastening unit from turning if...
Removal and installation the hinge in the swivel support 1. Remove the front wheel. 2. Loosen the nut (1), holding the fastening unit from turning if...
Left and right thrust
Removal and installation the left or right tie rod Attention: In the 12/2006 design, the connection between the tie rod and the guide joint is reinforced by 10...
Removal and installation the left or right tie rod Attention: In the 12/2006 design, the connection between the tie rod and the guide joint is reinforced by 10...
Rotary support
Removal and installation the left or right swivel support 1. Remove the front wheel. Caution: Spread the angular locking device wide enough to avoid damaging...
Removal and installation the left or right swivel support 1. Remove the front wheel. Caution: Spread the angular locking device wide enough to avoid damaging...
Shock absorber strut
Removal and installation the left or right front shock absorber assembly Attention: If the centering pin at the upper shock absorber support is missing, then...
Removal and installation the left or right front shock absorber assembly Attention: If the centering pin at the upper shock absorber support is missing, then...
Disassembling the left or right front shock absorber strut
Attention: Before each use of the 313340 device, it is necessary to read the operating instructions from beginning to end. Strictly follow the safety rules and...
Attention: Before each use of the 313340 device, it is necessary to read the operating instructions from beginning to end. Strictly follow the safety rules and...
Assembling the left or right front shock absorber strut
1. Insert the spring into tools 313382 and 313383. 2. Turn the spring so that its lower end (1) coincides with the end (2) of the device. Attention: The spring...
1. Insert the spring into tools 313382 and 313383. 2. Turn the spring so that its lower end (1) coincides with the end (2) of the device. Attention: The spring...
Front anti-roll bar
Removal and installation the front anti-roll bar Caution: Secure the engine in its mounting position to prevent it from falling. 1. Disconnect both struts from...
Removal and installation the front anti-roll bar Caution: Secure the engine in its mounting position to prevent it from falling. 1. Disconnect both struts from...
Front ride height sensor
Removal and installation the front ride height sensor Caution: Follow the ESD protection instructions (ESD - Electrostatic Discharge). 1. Disconnect the...
Removal and installation the front ride height sensor Caution: Follow the ESD protection instructions (ESD - Electrostatic Discharge). 1. Disconnect the...
Checking the wheel alignment angles on the KDS under normal loading
Attention: Checking the wheel alignment angles with the vehicle loaded according to DIN should only be performed: if there are no technical conditions for...
Attention: Checking the wheel alignment angles with the vehicle loaded according to DIN should only be performed: if there are no technical conditions for...
Checking the wheel alignment angles on the KDS with ground clearance measurement when the vehicle is unloaded
Attention: Do not check the wheel alignment angles when the vehicle is loaded according to DIN: if there are no technical conditions for measurement with the...
Attention: Do not check the wheel alignment angles when the vehicle is loaded according to DIN: if there are no technical conditions for measurement with the...
Adjusting the positive toe-in and camber of the front wheels
Caution: Under no circumstances should changes in axle geometry caused by an accident be corrected by adjusting the camber angle. Note: The camber and toe...
Caution: Under no circumstances should changes in axle geometry caused by an accident be corrected by adjusting the camber angle. Note: The camber and toe...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections for other types of BMW cars:
Chassis: Front suspension BMW 3 Series E21 (1975-1983)
Chassis: Front suspension BMW 5 Series E12 (1972-1981)
Chassis: Front suspension BMW 7 Series E38 (1994-2001)
Chassis: Front suspension BMW X5 E53 (1999-2006)
Chassis: Front suspension BMW 3 Series E21 (1975-1983)
Chassis: Front suspension BMW 5 Series E12 (1972-1981)
Chassis: Front suspension BMW 7 Series E38 (1994-2001)
Chassis: Front suspension BMW X5 E53 (1999-2006)
Share information:
- General information
- Introduction to manual
- Troubleshooting
- User manual
- Maintenance
- Power unit
- Diesel engine M47 T2
- Diesel engine N47
- Diesel engine M57 T2/TU
- Petrol engine N46
- Petrol engine N52
- Petrol engine M54
- Cooling system
- Lubrication system
- Fuel system
- Engine management
- Intake and exhaust system
- Engine electrical equipment
- Transmission
- Clutch
- Gearbox and transfer case
- Drive shafts and axles
- Chassis
- Front suspension
- Rear suspension
- Brake system
- Steering system
- Body
- Exterior
- Doors and windows
- Safety system
- Air conditioner
- Electrical equipment
- Equipment and devices
- Lighting and signaling
- Electrical circuits