1. Clean the surfaces of the intermediate shaft bearings and the bearing bushings pressed into the cylinder block.
2. Lubricate the shaft and insert it into the block.
3. Install the two mounting bolts to the retaining plate block.
4. The remaining parts are installed in the reverse order of removal.
[Information obtained from this online resource «BMWman.ru»]
- Home
- BMW 5 Series
- E28
- Power unit
- Engine overhaul
- Installing the intermediate shaft
Installing the intermediate shaft (BMW 5 Series E28)
This article is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Article verified: Zhuravleva Isolda
Share information:
Previous articles
БМВ E28: Engine overhaul
Next articles
Similar articles on other types of BMW cars:
Removal and installation the intermediate shaft BMW 3 Series E21 (1975-1983)
Cardan shaft intermediate support bearing — inspection and replacement BMW 3 Series E46 (1998-2006, petrol)
Replacing the intermediate support of the propeller shaft BMW 7 Series E38 (1994-2001)
Idle speed control valve — checking, removing and installing BMW 7 Series E32 (1986-1994)
Gear selector shaft sealing ring (GS 6 — 37 bz) BMW X3 E83 (2003-2010)
Replacing the intermediate support of the propeller shaft BMW X5 E53 (1999-2006)
Removal and installation the intermediate shaft BMW 3 Series E21 (1975-1983)
Cardan shaft intermediate support bearing — inspection and replacement BMW 3 Series E46 (1998-2006, petrol)
Replacing the intermediate support of the propeller shaft BMW 7 Series E38 (1994-2001)
Idle speed control valve — checking, removing and installing BMW 7 Series E32 (1986-1994)
Gear selector shaft sealing ring (GS 6 — 37 bz) BMW X3 E83 (2003-2010)
Replacing the intermediate support of the propeller shaft BMW X5 E53 (1999-2006)
Link in different formats to this page
Visitor comments
No comments yet
- General information
- Governing bodies
- Manual
- Maintenance
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Ignition system
- Supply system
- Injection system (gasoline)
- Injection system (diesel)
- Exhaust system
- Transmission
- Clutch
- Car gearbox
- Front axle
- Rear axle
- Chassis
- Steering
- Brake system
- Wheels and tires
- Body
- Interior
- Exterior
- Heating system
- Electrical equipment
- Equipment and devices
- Power devices
- Windscreen wipers
- Electrical circuits
- General information
- Manual
- Maintenance
- Power unit
- Engine repair
- Ignition system
- Engine lubrication system
- Cooling system
- Fuel system (gasoline)
- Fuel system (diesel)
- Exhaust system
- Transmission
- Clutch
- Car gearbox
- Chassis
- Front and rear suspension
- Steering
- Brake system
- Body
- Exterior
- Interior
- Electrical equipment
- Heating system
- Equipment and devices
- Power devices
- Electrical circuits
- General information
- Manual
- Maintenance
- Power unit
- Engine in a car
- Engine overhaul
- Cooling system
- Supply system
- Ignition system
- Control system
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Transmission line
- Chassis
- Steering
- Front suspension
- Rear suspension
- Brake system
- Body
- Body elements
- Car care and painting
- Electrical equipment
- Heater and air conditioner
- Equipment and devices
- Starter and generator
- Electrical circuits
- General information
- Operation and maintenance
- Specifications
- Power unit
- Engine repair
- Cooling and lubrication system
- Supply system
- Ecotronic power supply system
- Fuel injection system
- Ignition system
- Transmission
- Clutch
- Gearbox BMW 242/4
- Gearbox Getrag 262/8
- Gearbox Getrag 265/6
- Automatic gearbox
- Cardan gear
- Rear axle
- Chassis
- Steering
- Front suspension
- Rear suspension
- Brake system
- Electrical equipment
- Equipment and devices
- Electrical circuits