Description of the body structure
Attention! When carrying out work in the area where the airbag system is located (door panels, front panel, interior trim) you should turn off the ignition and...
Attention! When carrying out work in the area where the airbag system is located (door panels, front panel, interior trim) you should turn off the ignition and...
Front bumper — design description
The front bumper is designed as a crossbar with a front shield (Fig. 18.3), which is covered with a lining (Fig. 18.4), which allows it to withstand an impact...
The front bumper is designed as a crossbar with a front shield (Fig. 18.3), which is covered with a lining (Fig. 18.4), which allows it to withstand an impact...
Replacing the front bumper trim
The replacement of the front bumper trim must be carried out in the following order. Prepare rubber plugs for the headlight washer hoses. Cut the bandage (1,...
The replacement of the front bumper trim must be carried out in the following order. Prepare rubber plugs for the headlight washer hoses. Cut the bandage (1,...
Replacing the cross beam of the cladding
Removing the cross beam (brackets) the front bumper trim on the cross member must be installed in the following order: Remove the front auxiliary engine...
Removing the cross beam (brackets) the front bumper trim on the cross member must be installed in the following order: Remove the front auxiliary engine...
Rear bumper — design description
The rear bumper is designed in such a way that it can withstand a car impact at a speed of up to 4 km/h without damage. At a speed of 15 km/h, the energy is...
The rear bumper is designed in such a way that it can withstand a car impact at a speed of up to 4 km/h without damage. At a speed of 15 km/h, the energy is...
Replacing the rear bumper
Attention! If there is a "PDC" system, it is necessary to disconnect the plug connectors (PC) of the system and remove the cable. When removing the bumper,...
Attention! If there is a "PDC" system, it is necessary to disconnect the plug connectors (PC) of the system and remove the cable. When removing the bumper,...
Replacing the rear bumper trim
If you are replacing the rear bumper trim, you must remove it and use the rear bumper beam to install the new trim in the following order. Remove the rear...
If you are replacing the rear bumper trim, you must remove it and use the rear bumper beam to install the new trim in the following order. Remove the rear...
Replacing the front fender
Front wing (fig. 18.18) stamped, removable, attached to the body frame with self-tapping screws and Torx screws. Attention! When replacing a wing, avoid...
Front wing (fig. 18.18) stamped, removable, attached to the body frame with self-tapping screws and Torx screws. Attention! When replacing a wing, avoid...
Hood — removal, installation and adjustment
The hood of the car provides access to its engine compartment, its design is shown in Figure 18.20. The hood must be removed with an assistant, in the...
The hood of the car provides access to its engine compartment, its design is shown in Figure 18.20. The hood must be removed with an assistant, in the...
Removal and installation the outside rearview mirror
The removal of the outside rearview mirror on the front left/right door must be carried out in the following order. Remove the speaker on the window frame of...
The removal of the outside rearview mirror on the front left/right door must be carried out in the following order. Remove the speaker on the window frame of...
Removal and installation the exterior mirror housing
Caution! When moving the exterior mirror housing, hold it only by the place closest to the body (1, Fig. 18.87) on the fairing drainage channel, otherwise the...
Caution! When moving the exterior mirror housing, hold it only by the place closest to the body (1, Fig. 18.87) on the fairing drainage channel, otherwise the...
Tightening torques for body element connections
Bumper with bracket to rear shock damper (M12) – torque 55 Nm. Shock damper and bracket to the body (M8) – torque 24 Nm. Rear view mirror to the front door...
Bumper with bracket to rear shock damper (M12) – torque 55 Nm. Shock damper and bracket to the body (M8) – torque 24 Nm. Rear view mirror to the front door...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections for other types of BMW cars:
Body: Exterior BMW 3 Series E46 (1998-2006)
Body: Exterior BMW 5 Series E39 (1995-2003)
Body: Exterior BMW 7 Series E38 (1994-2001)
Body: Exterior BMW X3 E83 (2003-2010)
Body: Exterior BMW 3 Series E46 (1998-2006)
Body: Exterior BMW 5 Series E39 (1995-2003)
Body: Exterior BMW 7 Series E38 (1994-2001)
Body: Exterior BMW X3 E83 (2003-2010)
Share information:
- General information
- Manual
- Maintenance
- M54 petrol engine
- Engine repair
- Lubrication system
- Cooling system
- Supply system
- Injection system
- Exhaust system
- Engine electrics
- M62 petrol engine
- Engine repair
- Lubrication system
- Cooling system
- Supply system
- Exhaust system
- Engine electrics
- N62 petrol engine
- Engine repair
- Cooling and lubrication system
- Power and exhaust system
- Engine electrics
- Diesel engine M57
- Engine repair
- Lubrication system
- Cooling system
- Power and exhaust system
- Engine electrics
- Turbocharging system
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Transfer case and cardan
- Chassis
- Brake system
- Steering
- Front suspension
- Rear suspension
- Wheels and tires
- Body
- Exterior
- Interior
- Doors and windows
- Repair and maintenance
- Heater and air conditioner
- Electrical equipment
- Equipment and devices
- Levers and switches
- Electrical circuits