- Home
- BMW X5
- E53
- M62 petrol engine
- Engine electrics
Electrical equipment of M62 engine of car BMW X5 E53
Removal and installation the generator
The M62 engine is equipped with a three-phase generator (fig. 4.121) alternating voltage, with a built-in rectifier unit on nine rectifier valves, with a...
The M62 engine is equipped with a three-phase generator (fig. 4.121) alternating voltage, with a built-in rectifier unit on nine rectifier valves, with a...
Removal and installation the alternator drive belt
The design of the generator drive tensioner is shown in Figure 4.123, the location of the drive belt on the pulleys of the engine auxiliary units is shown in...
The design of the generator drive tensioner is shown in Figure 4.123, the location of the drive belt on the pulleys of the engine auxiliary units is shown in...
Removal and installation the starter
The starter and retractor relay must be replaced from below, in the following order. Turn off the ignition, disconnect the "-" terminal from the battery....
The starter and retractor relay must be replaced from below, in the following order. Turn off the ignition, disconnect the "-" terminal from the battery....
Removal and installation of KSUD elements
The engine control automation includes control system sensors (see fig. 4.20) and the electronic control unit (ECU) KSUD, which has its own specific program....
The engine control automation includes control system sensors (see fig. 4.20) and the electronic control unit (ECU) KSUD, which has its own specific program....
Replacing the crankshaft speed sensor
The crankshaft speed sensor is installed under the starter, on the automatic transmission housing, and it must be replaced in the following order. Prepare the...
The crankshaft speed sensor is installed under the starter, on the automatic transmission housing, and it must be replaced in the following order. Prepare the...
Replacing the left intake camshaft position sensor
The left intake camshaft position sensor is located on the cylinder head and must be replaced in the following order. Read information from the DME ECU-KSUD...
The left intake camshaft position sensor is located on the cylinder head and must be replaced in the following order. Read information from the DME ECU-KSUD...
Replacing the right intake camshaft position sensor
The right intake camshaft position sensor is located at the front of the cylinder head next to the oil dipstick tube and must be replaced in the following...
The right intake camshaft position sensor is located at the front of the cylinder head next to the oil dipstick tube and must be replaced in the following...
Replacing knock sensors
Attention! Avoid interchanging the places of the plug connectors (PC) of the knock sensors. This will lead to engine failure. Mark them with color or numbers....
Attention! Avoid interchanging the places of the plug connectors (PC) of the knock sensors. This will lead to engine failure. Mark them with color or numbers....
Replacing the oil pressure sensor
A sensor is installed on the oil filter housing (23, see Fig. 4.14) oil pressure, it must be replaced in the following order, turn off the ignition and unscrew...
A sensor is installed on the oil filter housing (23, see Fig. 4.14) oil pressure, it must be replaced in the following order, turn off the ignition and unscrew...
Replacing the oil level sensor
The oil level sensor must be replaced in the following order. Turn off the ignition, unscrew the oil filter cap so that the oil flows into the engine oil pan....
The oil level sensor must be replaced in the following order. Turn off the ignition, unscrew the oil filter cap so that the oil flows into the engine oil pan....
Replacing the coolant temperature sensor
Attention! Perform work on a cooled engine. The coolant temperature sensor must be replaced in the following order: Read information from the fault memory of...
Attention! Perform work on a cooled engine. The coolant temperature sensor must be replaced in the following order: Read information from the fault memory of...
Replacing the ignition coil
The ignition coil must be replaced in the following order: Turn off the ignition, remove the plugs from the ignition coil protective casing, unscrew the nuts,...
The ignition coil must be replaced in the following order: Turn off the ignition, remove the plugs from the ignition coil protective casing, unscrew the nuts,...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections for other types of BMW cars:
Power unit: Engine electrical equipment BMW X3 E83 (2003-2010)
Power unit: Engine electrical equipment BMW X3 E83 (2003-2010)
Share information:
- General information
- Manual
- Maintenance
- M54 petrol engine
- Engine repair
- Lubrication system
- Cooling system
- Supply system
- Injection system
- Exhaust system
- Engine electrics
- M62 petrol engine
- Engine repair
- Lubrication system
- Cooling system
- Supply system
- Exhaust system
- Engine electrics
- N62 petrol engine
- Engine repair
- Cooling and lubrication system
- Power and exhaust system
- Engine electrics
- Diesel engine M57
- Engine repair
- Lubrication system
- Cooling system
- Power and exhaust system
- Engine electrics
- Turbocharging system
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Transfer case and cardan
- Chassis
- Brake system
- Steering
- Front suspension
- Rear suspension
- Wheels and tires
- Body
- Exterior
- Interior
- Doors and windows
- Repair and maintenance
- Heater and air conditioner
- Electrical equipment
- Equipment and devices
- Levers and switches
- Electrical circuits